83mm Build Update


Uncategorized / Tuesday, November 7th, 2017

Hello everyone welcome back.

Todays video is an update on the new 83mm brushless build I have been working on. I added a new camera mount. New standoffs so its not so tall. I also added motor guards and landing gear.

Here are the full specs for the build

BetaFPV 83mm Carbon Fiber Frame
Recommend motors: 1102 1103 1104 brushless motors
Wheelbase: 83mm
Plate Thickness:2.0mm
Weight: 10g
Form Factor: 16mm x 16mm

http://amzn.to/2i9CyPZ

USAQ Betaflight F3 Micro 6A 2S 4-In-1 Brushless ESC OSD Flight Controller Micro Cube
Flight Controller Specifications:
Dimensions: 20*20mm
Mounting Dimensions: 16*16mm
Weight: 1.9g
Processor: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000 ( connected by SPI)
Firmware version: betaflight_3.1.0_OMNIBUS
Built-in BEC: 5V/0.5A
Receiver: PPM, Spektrum 1024/2048, SBUS, IBUS, XBUS, SumD SumH RX etc.
Power supply: 2S lipo battery ( 6.5V-8.4V)
Suitable for 60mm-80mm mini brushless FPV Quadcopter frame

ESC Specifications:
Item name: 4 In 1 6A BLHeli_S ESC
Size: 25x29mm (includes solder pad)
Mounting holes: 16x16mm, φ2mm
Weight: 3g
Input voltage: 2S lipo
Con. Current: 6A
Peak Current: 10A (5S)
Firmware: BLHELI_S
Processor: SILABS EFM8BB21F16G
BEC: NO
Driver: 3 in 1 MOS
Supports Dshot Oneshot multishot

Features:
-Support programmable LED Sprit (turn off transponder before using)
-Support BLheli/BLHELI_S suite Pass-through ready
-Support PPM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
-Default Dshot600
-Built-in voltage detection, alarm
-Built-in Betaflight-OSD
-Buzzer solder pin
-LED_STRIP connector

Package included:
1* Super_S F3 flight control board
1* Super_S BS06D 6A 4in1 ESC
8*M2*5+5 Nylon column
8*M2 Nuts
8*M2 Screw

http://amzn.to/2yd5fT1

BetaFPV 1103b 10,000kv Brushless Motors
Height: 15mm
Width: 13.6mm
Weight: about 3.7g
Shaft: 1.5mm
KV: 10000KV

No longer available via BetaFPV. Here are some similar motors

http://amzn.to/2yfmxip

BetaFPV 1735 4 Blade Props
Material: PC plastic
Length: 1.7 inch, about 43.2mm
Color: white, orange, purple, green, blue, red
Mounting hole: 1.5mm
Weight: 0.8g per piece
Applicable for 1102, 1103, 1104, 1105, 1106, 11xx motors

http://amzn.to/2zVWC0m

BetaFPV H01 AIO FPV Camera
Output power: 25mW
Supply Voltage: 2.9-5.5v
Weight: 3.6g
Antenna: Dipole
Frequency: 5.8GHz 40 Channels
FOV: 120

http://amzn.to/2i9DuDZ

M2 Standoff kit
http://amzn.to/2yfXFGY

Motor Guards by Makerfire
http://amzn.to/2zDdD2u

Camera mount for 16mmx16mm by RJX Hobby
http://amzn.to/2yeSHKI

BetaFPV 450mah 2s Lipos

http://amzn.to/2yFlkoQ

If you have any questions about this build feel free to leave me a comment.

 

Thanks for watching

Fly Safe & Fly Often

 

Music by Ryan Little
Sub his channel
https://www.youtube.com/user/TheR4C2010

 

Leave a Reply